TROPICAL FISH RUB ON INSTANT STENCIL LUV TATOUAGE Start Price USD 3.89 Current Price USD 3.89 Time Left - Bid Count 0 Buy It Now Price USD 4.29 Reserve Price - Start Time Friday, September 05, 2008 End Time Friday, September 12, 2008 Location STATEN ISLAND NEW YORK See more about 'TROPICAL FISH RUB ON INSTANT STENCIL LUV TATOUAGE' Description Before you bid, we would just like YOU TO KNOW that our feedback rating was 99.4% positive for over 5years before ebay implemented their new totally unfair biased feedback policy    Measures 4" X 12"  RUB ONS  ARE EXACTLY LIKE YOUR HIGHER PRICED WALL ART WITH THE SAME HAND PAINTED LOOK FOR A MUCH MORE REASONABLE PRICE  AND  can be applied to the following surfaces: wall tile, stained wood, painted wood, glass, mirrors, painted walls, painted plaster and gypsum walls, ceramic, plastic, metal, cardboard, paper and strippable wallpaper. With each order you will get a wood applicator stick and a direction sheet.This product is NOT recommended for fabric or materials that wrinkle in use or cleaning, surfaces exposed to prolong intense heat, surfaces exposed to moisture (i.e. sinks or showers), surfaces exposed to excessive abrasion (i.e. floors), natural varnish finishes or shellac, vinyl wallpaper, or sharp or heavily textured surfaces. If there is a question regarding the application, test the stencil on a small, hidden area before beginning. DO NOT apply RUB ONS to surfaces intended to come in contact with food or surfaces that young children can place in their mouths (i.e. crib rails or plastic toys).     APPLICATION: 1. Before starting, make sure the surface is smooth, clean, sound and completely dry.   2. Plan the layout of the product with graph paper. Remember the Strips, Small Accessories and Large Accessories can be used alone or together to create a variety of looks.   3. Remove the protective liner from the RUB ONS and place the product, tacky side down, on the desired surface. RUBONS  can be repositioned on painted walls prior to rubbing the design on the surface.   4. Position and hold the stencil segment with one hand, rub briskly with the WOOD Applicator. Start in the upper left corner of the design, and rub with pressure in a back and forth motion. (Note: Seam roller tools can be used when pressure is applied.)   5. The pressure will cause the transfer process to begin. A change in color to a milky white will indicate the release of the stencil onto the surface. (Hint: Work on small sections at a time, concentrating extra time on areas with thin lines or great detail.)   6. Frequently check to insure the design is transferring by slowing lifting the carrier liner. If the design has not fully transferred, replace the liner and continue to rub until the color change occurs.   7. When the entire carrier sheet is milky white in color, it will easily slip from the surface to reveal the full design. At this point the carrier sheet will be void of color or design.   8. Allow the RUB ONS to bond to the surface for 48 hours before touching or cleaning.     9. Repeat steps 1-8 for each new segment or accessory.     10. If a surface coat or finish is desired, test a water-based product on a small area before beginning.     OTHER HINTS 1. Individual designs can be cut in countless ways to create new, unique designs. When cutting apart the stencil designs, leave the protective carrier liner attached to the stencil until it is applied to a surface. The Small Accessories should be cutout prior to application.   2. When applying the stencil to an inside or outside corner, cut the stencil exactly at the corner. Apply the first segment into the corner, match the design at the point of the cut, and apply the remaining piece. Simply wrapping the stencil at a corner will prevent the stencil from completely adhering to the wall.     CLEANING RUB ONS can be gently cleaned with a soft damp sponge, mild soap, and warm water. Do not apply excessive pressure when cleaning. This product is not recommended for dishwasher cleaning.     REMOVAL & REFINISHING: 1. Painted Wall Surfaces: Apply an appropriate barrier coating over the RUB ONS, allow sufficient drying time, apply paint or wallpaper as directed.     2. Non-Porous Surfaces (Tile, Glass, Ceramic, Metal): Apply baby oil or acetone-based fingernail polish remover to soften the adhesive. Clean with a paper towel. Work small areas of the design at a time, dissolving and removing the stencil color and adhesive. When using any type of remover, work in a well-ventilated area and insure proper safety precautions.     3. Wood Surfaces (Other Painted or Stained Surfaces): Lightly sand the stencil using paint stripper or acetone-based fingernail polish remover. The surface will have to be repainted or stained as the cleaner or sanding will affect the surface.     4. Some Plastic Surfaces: Place duct tape over the stencil, apply pressure with the applicator and pull the tape quickly from the surface. In some cases RUB ONS cannot be removed from plastic without damaging the surface, a ghost image of the design may remain on the plastic.  If you feel you need a small practice piece just send me an E-Mail and I will include a free piece with your order....                                                                                         Shipping and handling is a flat rate $ 3.99 FOR FIRST WINNING AUCTION ANY WINNING STENCIL AUCTION AFTER THAT WILL BE $1.50 THANKS outside U.S.A, Hawaii, Puerto Rico and Alaska please E-mail before bidding if you are unsure of shipping amount..I ship out USPS and will ship usually within 5 days of auction ending..I will comine shipping cost as long as each auction is ending within one week of each other...Please don't pay for an auction if you want to combine shipping cost, wait till all auctions are ended then i will send a combined payment...Thank you and please feel free to contact me with any concerns CHECKout my other items!Be sure to add me to your favorites list! Please check out my  other instant stencil RUB ONS  I have up for auction.   Powered by eBay Turbo Lister Place a Bid!